2022-05-30 | 8 inspections must be done before started

8 inspections must be done before started
INDUSTRIAL OR MANUFACTURERS NEWS ABOUT Machinery and Constraction
Read: 10250

share Copy page link
share Share link to: Facebook | Twitter
These 8 inspections must be done before the excavator is started, and none of them can be missed!

1. Check the coolant level
Be sure to wait for the engine to cool down before checking the radiator reservoir. If the coolant level is too low, add coolant to the specified position.

2. Check the oil level in the engine oil pan
Wait 15 minutes after the engine has been turned off before checking the oil level. When checking the oil level, the machine should be in a horizontal position. The oil level should be within the specified range.

3. Check diesel oil level
Check the diesel oil level through the observation window on the diesel tank, the oil level gauge or the monitor. If the oil level is too low, replenish the diesel oil and clean the ventilation holes on the diesel tank cover frequently.

4. Check hydraulic oil level
First, park the machine on a flat ground, start the engine and run at idle speed, retract the stick and bucket hydraulic cylinder, lower the boom, and make the bucket teeth touch the ground. After shutting down the engine, operate the lever to relieve internal pressure. At this point, check that the hydraulic oil level is between the upper and lower limits. Because the oil level changes with the oil temperature, the oil level should be at the lower limit position before operation (the oil temperature is between 10 and 30), and the oil level should be at the upper limit during normal operation (the oil temperature is between 50 and 80).

5. Check the air cleaner element
The filter element can be checked, cleaned or replaced according to the display or dust indicator etc.

6. Check electrical wiring
Check whether the fuse is damaged, there is an open circuit or short circuit in the line, and check whether the terminal is loose. If it is loose, tighten it. Carefully check the battery, starter motor, generator. Remove flammable materials around the battery in time. If the fuse is frequently burned out or there is a short circuit in the line, it should be repaired.


7. Check for water and sediment in the excavator oil-water separator
If there are deposits, they should be discarded immediately. When water is drained, if air is sucked into the diesel pipe, it must be released in the same way as the fuel filter.


8. Adjustment of Excavator Driver's Seat and Mirrors
Sit on the seat, recline the backrest, and adjust the position of the seat.
Maneuverable when pedals and levers are in neutral position. Adjust the mirrors on the seat to make it easy to see behind you through the mirrors.



NEW HW-20W Crawler Excavators
Machine weight: 1700Kg
Bucket Capacity: 0.045cbm
Rated Power: 13.6Kw

Selling point one
Excellent work efficiency and value for money

Selling point two
Equipped with a bulldozer, it can level the site, backfill the earth, and increase the stability of the whole machine

Selling point three
Simple operation, small and flexible, easy to transport, and can work in small places

Selling point four
It has the functions of excavation, crushing, ditch cleaning, drilling and bulldozing, and can quickly replace accessories,
greatly improving the utilization rate of the machine



Please see more about this item »
8 inspections must be done before started




Get more information from us

* Please enter your message in the box below:
(* denotes a mandatory field)


Title: *
Name: *
Company: *
Country: *
City*:
Phone Number:
E-Mail: *


Please write the result *

NEW DRILL RIGS & PILLING MACHINERY® latest arrivals

NEW DRILL RIGS & MACHINERY® the best offers

NEW PILLING MACHINERY® the best offers

NEW DRILL RIGS & PILLING MACHINERY® LATEST NEWS


Crazy Engineering Days Sale
Submit Form to Get Order Discount and $5,000 Off Coupon
Separated DTH Surface Drill Rig HW-916 is a trusted machine for mining and construction companies and contractors engaged
in presplitting and conventional production blasthole drilling.
Drilling diameter (mm) φ90-127 , Maximum torque (Nm 1950

  READ MORE  
NEW drilling machinery  and piling rigs Atlas Copco, Geoprobe
All of our drilling machinery and piling rigs and other equipment comes with a full warranty and is subjected to a thorough technical inspection and workshop service prior to delivery. Our sales team have a wealth of shipping experience, and will undertake all logistics as well as related paperwork on your behalf, to ensure the process is as turnkey, and hassle free, as possible.
Contact us with any questions about our products or any inquiries as to how you can become better educated about our production and finance.
We look forward to working with you to make your immediate environment more sustainable and efficient.

sitemap.xml for Google | Panorama photos created by wirestock - www.freepik.com

  My Cart


Save any items in your bag and when you're ready, just order.
CLICK HERE